Search found 1051 matches

by stevieturbo
Sun Oct 24, 2021 8:45 am
Forum: Feature Requests
Topic: Highlight cells in Scal tables
Replies: 3
Views: 12

Re: Highlight cells in Scal tables

export where or do what ?
by stevieturbo
Sat Oct 23, 2021 9:26 pm
Forum: Feature Requests
Topic: Highlight cells in Scal tables
Replies: 3
Views: 12

Re: Highlight cells in Scal tables

Toggle delta hotspots sort of does this for changes made.

But a tracer over the table like other ecu's would be nice too when doing quick lookbacks.
by stevieturbo
Thu Oct 21, 2021 6:00 pm
Forum: Technical Deposit
Topic: EGT probes
Replies: 92
Views: 55271

Re: EGT probes

not the Vaseline then ? lol
by stevieturbo
Wed Oct 20, 2021 5:13 pm
Forum: S7-I / S7Plus Technical
Topic: Blip to rev match
Replies: 4
Views: 727

Re: Blip to rev match

Unless you have sensor inputs to let the ECU know where you are going with the gear selector, it wont be possible. You have the ability on a H pattern box to go from say 5 to 4 or 3 or 2 etc.., and without a sensor on the gearbox the ECU wont know where you are going you wont know what to target th...
by stevieturbo
Fri Oct 15, 2021 8:46 pm
Forum: S7-I / S7Plus Technical
Topic: Output status when powered off
Replies: 2
Views: 579

Re: Output status when powered off

I believe you should be ok.

I run my fuel pumps via a SSR and a "permanent" fused supply to the SSR and have never had a problem
by stevieturbo
Fri Sep 17, 2021 1:59 pm
Forum: Feature Requests
Topic: Overrun Fuel Cut
Replies: 13
Views: 29488

Re: Overrun Fuel Cut

Gpro wrote: Wed Sep 15, 2021 1:49 pm another 4 years later, this feature still missing and makes sense to have.
Which feature ? there is an overrun fuel cut.
by stevieturbo
Mon Sep 06, 2021 12:56 pm
Forum: General Syvecs Chat
Topic: CAN Frame Frequency
Replies: 9
Views: 572

Re: CAN Frame Frequency

unless you have a BAP sensor, it will likely read whatever you have as default value for it, unless you have set it to read atmospheric at key on.

Not hugely relevant in many cases.
by stevieturbo
Mon Sep 06, 2021 9:09 am
Forum: General Syvecs Chat
Topic: Reducing Rev Hang
Replies: 3
Views: 321

Re: Reducing Rev Hang

for most part all that matters is if TPS is tracking TPS target properly.

if it is staying higher, that might cause revs to drop slower, or this plus too much fuel or timing or something.

Datalog it and see what is happening.
by stevieturbo
Mon Sep 06, 2021 9:01 am
Forum: General Syvecs Chat
Topic: CAN Frame Frequency
Replies: 9
Views: 572

Re: CAN Frame Frequency

Thanks both for the replies :) That's helpful and good to know i can increase the rate if needed. I was thinking of increasing things like AFR and idle / dbw error to get a better logging for tuning. How fast do you think a typical wideband is ? 100Hz is not necessary. And DBW control parameters, y...
by stevieturbo
Fri Sep 03, 2021 3:20 pm
Forum: General Syvecs Chat
Topic: CAN Frame Frequency
Replies: 9
Views: 572

Re: CAN Frame Frequency

On my S6 i can set each frame to send over CAN between 1hz and 100hz. Currently these are set with a few frames on 50hz and others on 5 and 10. Is there any limitation to increasing the frequency of the frames or is it just based on requirement? I'm sending CANbus data to RealDash and if i can send...