So I am going to assign secondary injector outputs 1-6 to six outputs and wire three outputs for one bank together for the injector. Same for the other bank.
As they are open collector, can I just put the three outputs on one injector or should I use a diode in-line on each output of the ECU?
Search found 7 matches
- Sat May 18, 2024 9:12 am
- Forum: Syvecs WMI Module
- Topic: Pwm fuel injector
- Replies: 6
- Views: 89433
- Wed May 15, 2024 2:50 pm
- Forum: Syvecs WMI Module
- Topic: Pwm fuel injector
- Replies: 6
- Views: 89433
Re: Pwm fuel injector
I want to use two injectors (one per bank on a six cylinder) with a F88. Would it be possible to set up WMI as secondary injectors and assign the three cylinders of one bank to one injector output? I would like to keep it syncronized to the crank, so the cylinders are getting an even distribution of...
- Mon Mar 25, 2024 5:51 pm
- Forum: S8 Technical
- Topic: Single Cylinder EGT average
- Replies: 1
- Views: 13234
Single Cylinder EGT average
I am running 6 K-type thermocouples on a V6 engine into a CAN-Bus transceiver. I am receiving these as user definable sensors on the F88. Is it possible to build an average math channel from the the individual cylinder on each side to use it as egt1/egt2 channel for lambda-target correction and ALS-...
- Tue Oct 24, 2023 9:07 am
- Forum: Technical Deposit
- Topic: EGT probes
- Replies: 134
- Views: 591349
Re: EGT probes
Do I understand correctly that you are injecting 4.113cm³/min fuel and 2.388cm³/min water?
That would be 58% WM (or even more if you calculate it in fuel mass). I Ihought that usually about 20% is the target?
Just trying to learn something...
That would be 58% WM (or even more if you calculate it in fuel mass). I Ihought that usually about 20% is the target?
Just trying to learn something...
- Tue Mar 07, 2023 8:31 am
- Forum: Syvecs WMI Module
- Topic: Recommended Parts for Water Meth Injection setups
- Replies: 19
- Views: 92674
Re: Recommended Parts for Water Meth Injection setups
I can add some infos on the Aquamist sensor. I just tested one. It works with a Syvecs ECU. Pinout: 1 red 5V Power supply 2 yellow Turbine Flow Sensor signal output 1mA max@5V 3 blue Feedback Signal (return ground) 4 black gnd These are from a Aquamist paper, I can not confirm these: 0ml/min 0Hz 250...
- Wed Oct 06, 2021 4:06 pm
- Forum: General Syvecs Chat
- Topic: More water / meth injection
- Replies: 99
- Views: 3056291
Re: More water / meth injection
For a more exact metering I want to use two Injectors (Bosch 0 280 158 827 NGI2) on a V6 engine for WMI injection. My thought was to wire these injectors as secondary fuel injectors (so they will be in sync with the engine) and fire WMI1 on cyl 123 and WMI2 on cyl 456. When I configure this in the p...
- Sun May 09, 2021 6:03 pm
- Forum: Technical Deposit
- Topic: Calibration needed for Bosch 0 280 750 151 throttle body (McLaren 650/720)
- Replies: 0
- Views: 36249
Calibration needed for Bosch 0 280 750 151 throttle body (McLaren 650/720)
I am running a F88 on a Renault 3L twin turbo engine. I am in the process of upgraqding the turbos and adding some more sensors.
I also decided to use two 60mm DBW throttle bodies. These are the Bosch units used on all current McLaren engines.
Can anyone help with a calibration?
I also decided to use two 60mm DBW throttle bodies. These are the Bosch units used on all current McLaren engines.
Can anyone help with a calibration?