Race Tech Dash2 Config Files Pack HERE

Pin outs, sensor calibrations etc
Ryan.g
Syvecs Staff - Caretaker
Posts: 498
Joined: Fri May 30, 2008 4:05 pm

Race Tech Dash2 Config Files Pack HERE

Post by Ryan.g »

Hi all

Here is the config pack for the Dash2

In the zip file you have:

Can adaptor flash file
Basic Dash2 config file
Syvecs cal file with Custom can bus data to match can adaptor config - PasteCal all Can stuff into your map

See attached

Ryan
Attachments
Syvecs RT Dash2 Package.zip
(265.92 KiB) Downloaded 2021 times
Ryan.g
Syvecs Staff - Caretaker
Posts: 498
Joined: Fri May 30, 2008 4:05 pm

Re: Race Tech Dash2 Config Files Pack HERE

Post by Ryan.g »

Found a slight error with the frame content on one of the sensors and now updated within the package above

Ryan
Wez
Santa's Little Helper
Posts: 267
Joined: Thu May 22, 2008 3:19 pm
Location: London

Re: Race Tech Dash2 Config Files Pack HERE

Post by Wez »

Top stuff matey, I was going to call you about these bits and pieces 8-)
96 MKIV Supra, S6GP, 591bhp & 523ft/lbs
wrxbart
Posts: 11
Joined: Mon Jun 15, 2009 11:23 pm

Re: Race Tech Dash2 Config Files Pack HERE

Post by wrxbart »

Hi tried to load your file onto my dash2 but it only gets to 99% then stops and the dash then goes into a fail mode with no back light and only parts of the dash working. You then have to do a dash 2 reflag with the original software to get it back to standard again. Any help available to sort this?
Ryan.g
Syvecs Staff - Caretaker
Posts: 498
Joined: Fri May 30, 2008 4:05 pm

Re: Race Tech Dash2 Config Files Pack HERE

Post by Ryan.g »

Hi Bart,

This must be an issue with the new Dash2 config software.

I would suggest speaking to Lorne at Race Technologies and send him config file

Ryan
wrxbart
Posts: 11
Joined: Mon Jun 15, 2009 11:23 pm

Re: Race Tech Dash2 Config Files Pack HERE

Post by wrxbart »

Ok many thanks mate will do.
tarmac terror
Posts: 30
Joined: Fri Apr 27, 2012 6:30 pm

Re: Race Tech Dash2 Config Files Pack HERE

Post by tarmac terror »

Has this now been resolved??

TT
Ryan.g
Syvecs Staff - Caretaker
Posts: 498
Joined: Fri May 30, 2008 4:05 pm

Re: Race Tech Dash2 Config Files Pack HERE

Post by Ryan.g »

Yes Lorne has updated so you can select Syvecs on software now.
ders
Posts: 13
Joined: Thu Jan 17, 2013 9:11 am

Re: Race Tech Dash2 Config Files Pack HERE

Post by ders »

Any information on how this interface will work with the new Dash 2 Pro, which is touting a direct 1M CAN interface? Or will we have to sit and wait for the 'comming soon' to be formally elaborated on by RT?
pavlo
Zen Performance
Posts: 407
Joined: Mon Aug 04, 2008 10:18 am

Re: Race Tech Dash2 Config Files Pack HERE

Post by pavlo »

It's easy. The new range of RT stuff is great, and the current software a quantum leap in terms of speed.

The new system means just unlock 15 CAN channels and configure them in the same way as you used to with can->serial adaptor. The Syvecs also outputs direct RT serial stream too.

The Dash 2 Pro is based on the new DL1 processor platform so some of the stuff is taking a little while to get ported over, but it's all coming along nicely, I spoke to Martin at RT a few days ago and they marching on with all that stuff.
Post Reply