Cheers Ryan.
I've ordered this:-
http://www.efi-parts.co.uk/index.php?productID=125
As you can see the calibration it gives is temp vs resistance. What's the best way of converting that to voltage?
Search found 42 matches
- Tue Apr 26, 2011 11:03 am
- Forum: Technical Deposit
- Topic: Water / oil / fuel temp sensors
- Replies: 8
- Views: 40746
- Wed Apr 13, 2011 2:49 pm
- Forum: Feature Requests
- Topic: Logging
- Replies: 14
- Views: 46238
Re: Logging
Have been having a think about the logging capability over the last few days. With all the channels logging at suitable rates I only get 178 seconds of logging time! I've been using SMON a fair bit recently to monitor stuff on the fly, would it be incredibly difficult to enable SMON to log to a HD a...
- Tue Apr 12, 2011 11:48 am
- Forum: Technical Deposit
- Topic: Water / oil / fuel temp sensors
- Replies: 8
- Views: 40746
Water / oil / fuel temp sensors
Can anyone recommend suitable water / oil / fuel temp sensors for use with the S6?
Thanks,
Tony
Thanks,
Tony
- Fri Mar 18, 2011 12:24 am
- Forum: Software
- Topic: Closed loop lambda control
- Replies: 5
- Views: 14086
Re: Closed loop lambda control
Cheers Pat. Wasn't sure if I was missing a trick! :) In order to calculate the injector time I think I would use the following: (fuelBase1* 1 *fuelMltLoad1*fuelMltEct1*fuelMltAct1*fuelMltBap*fuelMltCalSw*fuelMltCll1)-(fuelBase1* 1 *fuelMltLoad1*fuelMltEct1*fuelMltAct1*fuelMltBap*fuelMltCalSw) The va...
- Wed Mar 16, 2011 1:35 pm
- Forum: Software
- Topic: Closed loop lambda control
- Replies: 5
- Views: 14086
Re: Closed loop lambda control
Cheers Pat, that's spot on. Further to this however, I'd like to set up a math channel in SView that tells me what the injector correction is being made by the cll control in ms. This should be relatively easy to do (after all the calculation is shown in the help 8-) ) but the only thing that is scu...
Re: SView bug
Well you don't hang around!
- Mon Mar 14, 2011 12:39 am
- Forum: Software
- Topic: Closed loop lambda control
- Replies: 5
- Views: 14086
Closed loop lambda control
Perhaps someone can help me here... I'm trying to work out what it is that turns the lambda control off above certain engine loads. I've seen a few maps now that have lambda targets in the range of 14:1, but then the target all of a sudden drop to zero at say 10 - 16 PSI of MAP. I'm guessing the fac...
SView bug
When you create custom worksheets with multiple graphs with selected channels in SView and save it, if you swap to another worksheet and then swap back the channels are still selected on each graph (as you imagine it would be) but the Y axis and it's corresponding title are not shown. It's possible ...
- Thu Mar 10, 2011 12:29 am
- Forum: Software
- Topic: Sensor failure detection
- Replies: 1
- Views: 5153
Sensor failure detection
Can someone explain how the sensor failure detection works? In particular what I'm looking at is the EGT sensor. I understand about the failure rate and recovery rates and the default high and low voltages, but in this instance, how do the too low temp, too low time and too low run time settings wor...
- Thu Dec 30, 2010 5:46 pm
- Forum: General Syvecs Chat
- Topic: iPhone Syvecs Display / Monitor
- Replies: 31
- Views: 61609
Re: iPhone Syvecs Display / Monitor
Any updates Wez?
I think this could be really good!
I think this could be really good!