Search found 163 matches
- Fri May 03, 2024 2:01 pm
- Forum: S6-I / S6Plus Technical
- Topic: Bosch LSU 4.9 sensors dropping like flies
- Replies: 27
- Views: 98851
Re: Bosch LSU 4.9 sensors dropping like flies
Just to close the loop on this 5 years later - no I never did bring this to resolution - right now I'm looking at moving to NTK L2H2 instead - just tryign to find out what needs to be done to make that happen - believe there is a solder bridge on the ECU board somewhere that needs changing.
- Tue Jan 09, 2018 12:02 pm
- Forum: General Syvecs Chat
- Topic: Engine starting issue
- Replies: 2
- Views: 6454
Re: Engine starting issue
Good idea - I should have a cal of the same firmware revision that I could quickly pop on there to see. Cheers.
- Thu Jan 04, 2018 3:21 pm
- Forum: General Syvecs Chat
- Topic: Engine starting issue
- Replies: 2
- Views: 6454
Engine starting issue
Bit of a head scratcher this one - and probably more a general ecu calibration thing than syvecs specific: Some time back I re calibrated the linearization of my map sensor - I had an old an incorrect linearization the syvecs was reading slightly out. That meant I needed to re-work a fair bit of my ...
- Thu Nov 09, 2017 7:44 pm
- Forum: General Syvecs Chat
- Topic: "could not open device for streaming"
- Replies: 5
- Views: 11269
Re: "could not open device for streaming"
Cheers Slowie! I didn't realise that!
- Thu Nov 09, 2017 10:44 am
- Forum: General Syvecs Chat
- Topic: "could not open device for streaming"
- Replies: 5
- Views: 11269
Re: "could not open device for streaming"
Thanks chaps - mine turned out to be related to the fact that the engine wasn't actually 'running' at the time - was trying to capture start up knock signal and include in the overall streamed log - hadn't ever had need to do this - didn't note that the steaming doesn't start until engine is actuall...
- Wed Nov 08, 2017 12:45 pm
- Forum: General Syvecs Chat
- Topic: "could not open device for streaming"
- Replies: 5
- Views: 11269
"could not open device for streaming"
Got this errror yesterday after successfully streaming data, analysing and then going back for another run. Same laptop, same SS version, same cal, same everything - also i can still download logs and read program cals etc etc. Not dug too far into this - like swapping out current laptop for my old ...
- Wed Nov 08, 2017 12:41 pm
- Forum: General Syvecs Chat
- Topic: KnockWarnLight - how to test
- Replies: 5
- Views: 11166
Re: KnockWarnLight - how to test
I *thought* I had - but did not see anything triggered on the knockwarnlight - logs also confirmed it didn't activate.
The swapping in pitSwitch param to the data stream did prove out the Plex warning 'works' - in theory - I'll likely revisit with knockwarnlight when i get a moment.
The swapping in pitSwitch param to the data stream did prove out the Plex warning 'works' - in theory - I'll likely revisit with knockwarnlight when i get a moment.
- Tue Nov 07, 2017 8:30 am
- Forum: General Syvecs Chat
- Topic: KnockWarnLight - how to test
- Replies: 5
- Views: 11166
Re: KnockWarnLight - how to test
Ah yes that should do the job! I'll give that a whirl.
- Mon Nov 06, 2017 2:32 pm
- Forum: General Syvecs Chat
- Topic: KnockWarnLight - how to test
- Replies: 5
- Views: 11166
KnockWarnLight - how to test
Stumped on this one: I'm trying to configure KnockWarnLight to trigger the knock alarm on my Plex uSDM 102. KnockWarnLight is set to frame 14, slot 4 of the custom can content. I'm using y=(1*x)+0 to convert on the plex end. I'm seeing a value of "0" on the plex when KnockWarnLight is &quo...
- Tue Sep 19, 2017 3:43 pm
- Forum: General Syvecs Chat
- Topic: Knock sensor gain tuning - best practice
- Replies: 0
- Views: 28749
Knock sensor gain tuning - best practice
Playing around with knock sensor gain tuning I began to wonder what the best practice for setting up overall gain control along with individual gain tuning - heres how I've approached it on my EJ22: - Set all cylinder individual gains to 1 - Set overall gain to get my **quietest** cylinder (cyl1) ar...