Search found 8 matches
- Mon Mar 11, 2024 8:57 pm
- Forum: General Syvecs Chat
- Topic: Use Sview Math to Invert the output of a channel
- Replies: 1
- Views: 881
Use Sview Math to Invert the output of a channel
Hi guys, I understand "wg3maperrpct1" essentially outputs the invert of what its actually doing, so I was wondering if anyone could point me in the direction of how to build a math channel to flip the sign from negative to positive or visa versa. I was trying to figure out out how to get t...
- Tue Oct 03, 2023 7:38 pm
- Forum: General Syvecs Chat
- Topic: Increasing logging capacity for endurance races
- Replies: 10
- Views: 21751
Re: Increasing logging capacity for endurance races
S7+ ECU, nothing in the Syvecs range has near enough for a several hour long endurance race.
Is there a way to stream to a laptop via full logging or would it just be via the gauges?
Thanks!
Is there a way to stream to a laptop via full logging or would it just be via the gauges?
Thanks!
- Tue Oct 03, 2023 3:43 am
- Forum: General Syvecs Chat
- Topic: Increasing logging capacity for endurance races
- Replies: 10
- Views: 21751
Increasing logging capacity for endurance races
Do you guys know of a way we can increase logging capacity for endurance racing?
Thank you!
Thank you!
- Thu Jul 27, 2023 1:20 am
- Forum: General Syvecs Chat
- Topic: Failure Rate and Recovery Rate
- Replies: 5
- Views: 5076
Failure Rate and Recovery Rate
Hi there, Maybe I am not understanding the terminology but with regard to these two items: -Does increasing the failure rate make the time to failure increment more quickly or less quickly? -does increasing the recover rate allow the sensor to be considered "recovered" more quickly or less...
- Wed Jun 07, 2023 4:36 pm
- Forum: General Syvecs Chat
- Topic: Converting Error Flag Bits to Fault
- Replies: 4
- Views: 1307
Re: Converting Error Flag Bits to Fault
@littlefella thank you for looking.
I've attached a screenshot with the cursor on limp mode; error flag is 1024 (lambda 2 in my case) and limp mode shows "sensor warning level".
I'm not seeing the decode like yours, maybe I'm missing where to look. Thanks again for the help.
I've attached a screenshot with the cursor on limp mode; error flag is 1024 (lambda 2 in my case) and limp mode shows "sensor warning level".
I'm not seeing the decode like yours, maybe I'm missing where to look. Thanks again for the help.
- Mon Jun 05, 2023 6:06 pm
- Forum: General Syvecs Chat
- Topic: Converting Error Flag Bits to Fault
- Replies: 4
- Views: 1307
Converting Error Flag Bits to Fault
I looked in the manual and at the videos, and could not find an explanation on how to convert the error flag number that is produced by the log to the actual error specified by the "error flag items bit assignments". I do understand how to set the severity by group, but not how to determin...
- Fri Jun 02, 2023 4:05 pm
- Forum: Software
- Topic: Datalogging not stopping
- Replies: 4
- Views: 15785
Re: Datalogging not stopping
Will do, car is remote so not always able to go live.
My understanding from most logging programs is start speed 2500 will start it above 2500, and stop it below 2000, after its below 2000 for the delay period.
My understanding from most logging programs is start speed 2500 will start it above 2500, and stop it below 2000, after its below 2000 for the delay period.
- Wed May 31, 2023 7:59 pm
- Forum: Software
- Topic: Datalogging not stopping
- Replies: 4
- Views: 15785
Datalogging not stopping
Hi guys, I have datalogging enabled on all cal switches, and it starts at 2500RPM as expected but does not stop below 2000RPM (and when off throttle) Can you look and see if you can find my error? Log continually: no Log when syncstate is not stop: no datalogging start speed: 2500 datalogging stop s...