Search found 162 matches
- Tue Aug 22, 2017 12:56 pm
- Forum: S6-I / S6Plus Technical
- Topic: DCCD wiring / pin question
- Replies: 0
- Views: 24129
DCCD wiring / pin question
Hi have a DCCD wiring / pin question as is relateds to the S6Plus. My pinouts are configured as: H-Bridge7 / SlaveOut7H-Bridge7 / SlaveOut7H-Bridge7 / SlaveOut7 --> DCCD+ H-Bridge8 / SlaveOut8H-Bridge8 / SlaveOut8H-Bridge8 / SlaveOut8 --> DCCD- In terms on ECU I/O config, am I simply assigning: Outp...
- Mon Aug 21, 2017 3:57 pm
- Forum: Subaru
- Topic: No vehicle speed output - v3 GC8
- Replies: 1
- Views: 8684
Re: No vehicle speed output - v3 GC8
Cracked it - wrong input type - needed to be thermistor:
For the record:
config: RADAR = Thermocouple
filters: RADAR = On
teeth: RADAR = 3 (gives a very slightly high kph reading)
tyre size: 1.895
For the record:
config: RADAR = Thermocouple
filters: RADAR = On
teeth: RADAR = 3 (gives a very slightly high kph reading)
tyre size: 1.895
- Mon Aug 21, 2017 12:58 pm
- Forum: Subaru
- Topic: No vehicle speed output - v3 GC8
- Replies: 1
- Views: 8684
No vehicle speed output - v3 GC8
Hi - I wonder if anyone else has had this issue - I've been trying to get my vehicle speed input working on a S6plus - however I don't seem to have any output at all from the speedo. Having rung through the wiring and tested the input (AN05) is connected and configured correctly I'v confident that s...
- Fri Aug 18, 2017 12:36 pm
- Forum: General Syvecs Chat
- Topic: Errant(?) lean on load - anyone had this (ever)
- Replies: 10
- Views: 20403
Re: Errant(?) lean on load - anyone had this (ever)
Cheers Stevie - *little secret* - not running and closed loop corrections at present - partly as I had a load of problems a while ago with that faulty LSU 4.9 control circuit and partly because I then never retrospectively went back and made an attempt to set it up properly.
- Fri Aug 18, 2017 11:25 am
- Forum: General Syvecs Chat
- Topic: Errant(?) lean on load - anyone had this (ever)
- Replies: 10
- Views: 20403
Re: Errant(?) lean on load - anyone had this (ever)
Caught this in the logs this morning - looks like I have a failing / failed LSU 4.9.
Interestingly i did no realise once tripped the trip remains in place - until I imagine ECU power cycle?
log attached:
Interestingly i did no realise once tripped the trip remains in place - until I imagine ECU power cycle?
log attached:
- Wed Aug 16, 2017 4:05 pm
- Forum: General Syvecs Chat
- Topic: Plex / Syvecs logs.
- Replies: 2
- Views: 6242
Plex / Syvecs logs.
Plex's newly relased data analysis software got me thinking once again about logging solutions. I'd always intended on going to a SDM-500 as a dash / logging solution (as I've never been too happy with the onboard 1MB of the S6 Plus but hadn't looked into it in too much detail. Something has occured...
- Wed Aug 16, 2017 1:07 pm
- Forum: General Syvecs Chat
- Topic: Defi and Syvecs 4bar disagreement!
- Replies: 32
- Views: 58189
Re: Defi and Syvecs 4bar disagreement!
So what you seem to be saying was the old sensor cal was incorrect ? You'll need to adjust the tables manually based around previous voltage/map vs new. ie, you'll have to compare old vs new and simply copy each row from the old table and apply it to the correct pressure row in the new table. ie if...
- Wed Aug 16, 2017 1:00 pm
- Forum: General Syvecs Chat
- Topic: Defi and Syvecs 4bar disagreement!
- Replies: 32
- Views: 58189
Re: Defi and Syvecs 4bar disagreement!
The CAL doesn't include any sensor linearisation files you've saved out to the sensor DB, and only shows the currently applied one. But if the Syvecs 4 bar really is a 4 bar - and it ought to be!! - then I am not surprised if the linearisation is the same as a KA (JTi) one. As said, every pressure ...
- Tue Aug 15, 2017 3:57 pm
- Forum: General Syvecs Chat
- Topic: Defi and Syvecs 4bar disagreement!
- Replies: 32
- Views: 58189
Re: Defi and Syvecs 4bar disagreement!
Got some time to test / calibrate today. Given that my leakdown gauge and DEFI pretty much match I'm going with them as being 'correct' For anyone interested I've attached the cal containing the new data: Syvecs 4bar (DEFI) is just the syvecs calibration against the measured (as accurately as I am a...
- Sat Aug 12, 2017 11:38 am
- Forum: General Syvecs Chat
- Topic: Defi and Syvecs 4bar disagreement!
- Replies: 32
- Views: 58189
Re: Defi and Syvecs 4bar disagreement!
Cheers chaps - I will test...