C13 is fine, it's a 5v input, and as the instructions clearly say, the Cartek outputs 12v when on. So active High.
As to whether that is your problem with car not running for more than 5s, no idea.
I would assume if engine was not enabled, it would not start or run at all.
Search found 1337 matches
- Sun Apr 07, 2024 8:27 pm
- Forum: General Syvecs Chat
- Topic: Engine Cut for cartek XR
- Replies: 22
- Views: 300
- Tue Apr 02, 2024 4:04 pm
- Forum: S8 Technical
- Topic: Do the S8 IGBT Outputs have Protection Diodes
- Replies: 8
- Views: 125
Re: Do the S8 IGBT Outputs have Protection Diodes
Not quite what I expected. Fuel outputs, referenced to battery ground. In their off state, the couple of outputs I measured were sitting at a few millivolts. IGN output ( not used for ignition coils ), this one with no relay plugged in was sitting around 6v, but with relay plugged in, changed to 12....
- Mon Apr 01, 2024 9:26 pm
- Forum: S8 Technical
- Topic: Do the S8 IGBT Outputs have Protection Diodes
- Replies: 8
- Views: 125
Re: Do the S8 IGBT Outputs have Protection Diodes
Unusual way to wire things. Could this be back feeding somewhere in the system and doing strange things ? Although you seem to say about the outputs pulling to ground, they would only do this when the ecu is powered and the output is active. In their off state, ecu on, they would float around 12v. A...
- Mon Apr 01, 2024 9:01 pm
- Forum: S8 Technical
- Topic: Do the S8 IGBT Outputs have Protection Diodes
- Replies: 8
- Views: 125
Re: Do the S8 IGBT Outputs have Protection Diodes
kill switch relay ?
Surely if kill switch, however you have it configured is open, nothing should have power ?
What sort of kill are you using and how is it wired ?
Surely if kill switch, however you have it configured is open, nothing should have power ?
What sort of kill are you using and how is it wired ?
- Mon Apr 01, 2024 8:18 pm
- Forum: S8 Technical
- Topic: Do the S8 IGBT Outputs have Protection Diodes
- Replies: 8
- Views: 125
Re: Do the S8 IGBT Outputs have Protection Diodes
Don't know the details inside But even the most recent S8 I did, I've a few IGN outputs operating relays and they all work fine. Although I've never measured voltage with no relay attached. I've other relays and also the Hella SSR on some of the FUEL outputs, again, no problems But in an off state, ...
- Mon Apr 01, 2024 2:37 pm
- Forum: S8 Technical
- Topic: Do the S8 IGBT Outputs have Protection Diodes
- Replies: 8
- Views: 125
Re: Do the S8 IGBT Outputs have Protection Diodes
Can't answer the question, but what are the issues ?
- Tue Mar 26, 2024 10:24 pm
- Forum: S6 GP/PnP Technical
- Topic: 2003 Ford Focus RS - sensors question ?
- Replies: 275
- Views: 2158166
Re: 2003 Ford Focus RS - sensors question ?
their names are not the standard names for shifts and cuts etc, so they must be using the custom tables to do something ?
No idea really.
No idea really.
- Tue Mar 26, 2024 9:59 pm
- Forum: S6 GP/PnP Technical
- Topic: 2003 Ford Focus RS - sensors question ?
- Replies: 275
- Views: 2158166
Re: 2003 Ford Focus RS - sensors question ?
When you compare them to what's happening at shifts, the gear cut and blip do definitely occur at a shift point when you view the slaveAN values.
So they are being seen
So they are being seen
- Tue Mar 26, 2024 8:29 pm
- Forum: S6 GP/PnP Technical
- Topic: 2003 Ford Focus RS - sensors question ?
- Replies: 275
- Views: 2158166
Re: 2003 Ford Focus RS - sensors question ?
Yes, what are they used for in the pin assignments ?
They must surely be assigned to something ?
They must surely be assigned to something ?
- Tue Mar 26, 2024 6:50 pm
- Forum: S6 GP/PnP Technical
- Topic: 2003 Ford Focus RS - sensors question ?
- Replies: 275
- Views: 2158166
Re: 2003 Ford Focus RS - sensors question ?
What are the relevant slaveAN inputs configured as in the I/O 's ?