Search found 43 matches
- Mon Aug 26, 2013 2:58 pm
- Forum: Syvecs Bluetooth Module
- Topic: Syvecs Bluetooth Module
- Replies: 11
- Views: 36886
Re: Syvecs Bluetooth Module
Now what we need is bluetooth/CAN or bluetooth/serial controller in one unit, so CAL's can be changed from the App on the phone.
- Mon Aug 26, 2013 2:55 pm
- Forum: S6 GP/PnP Technical
- Topic: CAN BUS Cal Switch
- Replies: 16
- Views: 30917
Re: CAN BUS Cal Switch
What would CAL override be used for?
- Mon Aug 26, 2013 2:26 pm
- Forum: S6 GP/PnP Technical
- Topic: CAN BUS Cal Switch
- Replies: 16
- Views: 30917
Re: CAN BUS Cal Switch
Would this also mean that options like Rolling anti-lag can be controlled by the CAN BUS or is it limited to Up/Down Cal/Trac Commands?
- Sun Aug 25, 2013 2:46 pm
- Forum: S6 GP/PnP Technical
- Topic: CAN BUS Cal Switch
- Replies: 16
- Views: 30917
Re: CAN BUS Cal Switch
Future Toucan owner here then when this is implemented
Hurry up
Hurry up
- Sun Aug 25, 2013 2:15 pm
- Forum: S6 GP/PnP Technical
- Topic: CAN BUS Cal Switch
- Replies: 16
- Views: 30917
Re: CAN BUS Cal Switch
Have I read it right that the CAL's can now be controlled via CANBUS on the S6 with the new firmware?
- Sun Jul 28, 2013 10:05 pm
- Forum: General Syvecs Chat
- Topic: Resistance to voltage conversion
- Replies: 5
- Views: 12915
Re: Resistance to voltage conversion
I have set most of it now I think, I have set them as close to the current breakpoints using the excel sheet above. With how they were set previously the ECU was seeing ACT of 60 when it should have been 30 and EOT of 160 when it should have seen 90 odd. So they were a little out. :D The sensors wer...
- Sun Jul 28, 2013 8:11 pm
- Forum: General Syvecs Chat
- Topic: Resistance to voltage conversion
- Replies: 5
- Views: 12915
Re: Resistance to voltage conversion
Excellent, thanks for that
Is it possible to change the sensor breakpoints or is it a case of matching it up as best as possible to the nearest voltage point?
Is it possible to change the sensor breakpoints or is it a case of matching it up as best as possible to the nearest voltage point?
- Sun Jul 28, 2013 5:58 pm
- Forum: General Syvecs Chat
- Topic: Resistance to voltage conversion
- Replies: 5
- Views: 12915
Resistance to voltage conversion
I have now fitted a new air temp sensor and a new oil temp sensor. They come with the temperature vs resistance table but I need to convert this into voltage to setup the linearisations in the sensor settings.
How can this be done?
Cheers
Steve
How can this be done?
Cheers
Steve
- Sun Jul 28, 2013 5:41 pm
- Forum: S6 GP/PnP Technical
- Topic: CAN BUS Cal Switch
- Replies: 16
- Views: 30917
Re: CAN BUS Cal Switch
Any update on being able to control the cal switches by using the CANBUS?
- Thu May 23, 2013 3:22 pm
- Forum: S6 GP/PnP Technical
- Topic: CAN BUS Cal Switch
- Replies: 16
- Views: 30917
Re: CAN BUS Cal Switch
So I can just remove the CAL switches for now and just leave it set on one setting via a laptop until this update happens?