Hi Tim,
I wasn't being clear. Yes, we are talking about the same thing
I somehow thought you were talking about an external gauge. I am quite sure that my thresholds should work but I will start with the values you gave me and try again. Thanks!
Jasper.
Search found 56 matches
- Mon Aug 08, 2011 5:57 pm
- Forum: S6 GP/PnP Technical
- Topic: Cal Switch settings
- Replies: 11
- Views: 26316
- Mon Aug 08, 2011 5:46 pm
- Forum: S6 GP/PnP Technical
- Topic: Cal Switch settings
- Replies: 11
- Views: 26316
Re: Cal Switch settings
Hi Tim, Cheers for the reply. At leat it seems I understand it correctly. What is the reason to add a gauge for reading the voltages? I thought it would be more important to check the voltages that the Syvecs reads back from the Cal. switch as this is what is used for determination of the correct Ca...
- Mon Aug 08, 2011 3:23 pm
- Forum: S6 GP/PnP Technical
- Topic: Small lean-outs on Tip-In
- Replies: 1
- Views: 4096
Small lean-outs on Tip-In
All, I have some Tip-In issues (Transient Fuelling). I have noticed that I always get small lean-out spike when doing a quick blip from say 1k rpm. I have added loads of fuel in the fuel map and it doesn't seem to make things better. I have played with the Transient Fuelling a lot and it also did no...
- Mon Aug 08, 2011 3:19 pm
- Forum: S6 GP/PnP Technical
- Topic: Cal Switch settings
- Replies: 11
- Views: 26316
Cal Switch settings
All, I have connected the CAL. SWITCH for quite a while but I cannot get it to change correctly from CAL01-CAL08. I am almost sure the settings are correct but for some reason it displays CAL05 on 2 settings and sometimes CAL06 on 2 settings. 1) CAL01, 02, 03, 04, 05, 05, 06, 07 2) CAL01, 02, 03, 04...
- Wed May 11, 2011 9:59 pm
- Forum: S6 GP/PnP Technical
- Topic: NTK L2H2 vs. LC-1 w/ LSU 7200 differences
- Replies: 5
- Views: 10516
Re: NTK L2H2 vs. LC-1 w/ LSU 7200 differences
Hi there! I appreciate your comment. However I have ran the LSU at the bellmouth and saw no changes vs. running it in the center pipe. I just think the NTK calibration is waayy off which is a bit unpleasant as I expected it to be quite accurate with the appropriate linearisation. I guess I am wrong ...
- Sat May 07, 2011 5:23 pm
- Forum: Feature Requests
- Topic: Bosch LSU 4.0/4.2/4.9 support
- Replies: 1
- Views: 5395
Bosch LSU 4.0/4.2/4.9 support
Hi gents, It would be nice to have full Bosch LSU 4.0/4.2/4.9 support. NTK sensors will be slowly fading out I believe and it seems the Bosch sensors are technically better after having read the following comparison about them which said: The Nernst cell is much smaller which allows for much faster ...
- Sat May 07, 2011 4:54 pm
- Forum: S6 GP/PnP Technical
- Topic: NTK L2H2 vs. LC-1 w/ LSU 7200 differences
- Replies: 5
- Views: 10516
NTK L2H2 vs. LC-1 w/ LSU 7200 differences
Dear Syvecs Users/Pat, I have received NTK sensors from Charlie and have connected one directly to the Syvecs S6GP that I run. After getting it up and running I did some runs with NTK sensor mounted in the Bellmouth of the downpipe and the LC-1 w/ LSU 7200 sensor (that I used to map the car) in the ...
- Wed Mar 30, 2011 4:28 pm
- Forum: Feature Requests
- Topic: Toggle between Injector MS. and IDCs
- Replies: 1
- Views: 4804
Toggle between Injector MS. and IDCs
It would be nice to have a toggle which can display the Fuelmap in Injector MS. (Already has that now) as well as IDCs. I do it manually now in Excel to have a quick look but it should be a really easy thing to do it in the software. EG. IDC % = (Inj. MS * RPM) / 1200 Also it would perhaps be nice t...
- Tue Sep 21, 2010 5:23 pm
- Forum: S6 GP/PnP Technical
- Topic: Output to drive DCCD ?
- Replies: 16
- Views: 30972
Re: Output to drive DCCD ?
I would say if an aux. output is a PWM controlled output then it could work. If it's not you probably need an injector output which is a PWM based output. Stand ready to be corrected though as I'm still a Syvecs NOOB unfortunately
Cheers,
Jasper.
Cheers,
Jasper.
- Mon Aug 23, 2010 2:14 pm
- Forum: S6 GP/PnP Technical
- Topic: S6GP 1.17.1 A/C Firmware......Pat?
- Replies: 1
- Views: 4194
Re: S6GP 1.17.1 A/C Firmware......Pat?
Hiya Pat!
Big Cheers as I managed to get you on the phone and with your excellent help as always I should have it sorted now and my thoughts were basically confirmed. Good to know I was thinking in the right direction.
Cheers,
Jasper Kopinga
CS Racing
Taiwan.
Big Cheers as I managed to get you on the phone and with your excellent help as always I should have it sorted now and my thoughts were basically confirmed. Good to know I was thinking in the right direction.
Cheers,
Jasper Kopinga
CS Racing
Taiwan.