Search found 35 matches

by shmed
Tue May 26, 2020 8:48 am
Forum: S6 GP/PnP Technical
Topic: Syvecs CAN to Arduino
Replies: 8
Views: 5920

Re: Syvecs CAN to Arduino

I had mixed results with the different CAN boards iirc. I never managed to get the SparkFun board to work, but the Seeed Studios was quite easy(?)!

Then moved to the ST boards and ran out of skill.
by shmed
Tue May 26, 2020 8:37 am
Forum: S6 GP/PnP Technical
Topic: Syvecs CAN to Arduino
Replies: 8
Views: 5920

Re: Syvecs CAN to Arduino

I recall that I was moving away from the Arduino to a ST Micro based board with integrated CAN module.
by shmed
Mon May 25, 2020 12:00 pm
Forum: S6 GP/PnP Technical
Topic: Syvecs CAN to Arduino
Replies: 8
Views: 5920

Re: Syvecs CAN to Arduino

Five years on, you'd hope so....

In a fashion, yes, but life got in the way and I never finished it off. Haven't looked at it for a few years now so no idea what state it's in
by shmed
Thu Feb 23, 2017 10:08 am
Forum: S6 GP/PnP Technical
Topic: Cartek Isolator
Replies: 11
Views: 16992

Re: Cartek Isolator

Distance between the battery and alternator is quite large in the mr2...

Is the cartek actually msa approved?
by shmed
Wed Feb 22, 2017 10:46 am
Forum: S6 GP/PnP Technical
Topic: Cartek Isolator
Replies: 11
Views: 16992

Re: Cartek Isolator

Fair point. I'm also developing a PDM so I guess I could use the signal from the Cartek to do 'stuff' before the power goes. Not sure what though :D
by shmed
Tue Feb 21, 2017 12:17 pm
Forum: S6 GP/PnP Technical
Topic: Cartek Isolator
Replies: 11
Views: 16992

Re: Cartek Isolator

The XR model sends a signal to the ECU indicating that the kill switch has been activated. It then gives a small delay so the ECU can prepare the engine for the electrics to 'die'. I was wondering if the Syvecs could act on this signal to maybe pull some power from the engine before it unexpectedly ...
by shmed
Tue Feb 21, 2017 11:29 am
Forum: S6 GP/PnP Technical
Topic: Cartek Isolator
Replies: 11
Views: 16992

Cartek Isolator

Can the Syvecs S6 be used with the Cartek Battery Isolator XR?

I found something that said:
AN15 = AR3 Test Mode (D5 on EU or D14 on JDM) [KILL/ALS/LAUNCH/CAL]

Is any additional config required to make the ECU kill the engine?

http://www.cartekmotorsport.com/ISOLATO ... 0sheet.pdf
by shmed
Tue Oct 20, 2015 4:38 pm
Forum: General Syvecs Chat
Topic: Canbus specifications
Replies: 9
Views: 16661

Re: Canbus specifications

God,I'm such a bell end. Put the hex numbers together and I get the right value...
by shmed
Tue Oct 20, 2015 1:06 pm
Forum: Feature Requests
Topic: CANBUS control of TC
Replies: 34
Views: 60700

Re: CANBUS control of TC

Is there a list of CAN messages that the Syvecs S6 'listens' for?

Cheers

Paul
by shmed
Tue Oct 20, 2015 10:29 am
Forum: General Syvecs Chat
Topic: Canbus specifications
Replies: 9
Views: 16661

Re: Canbus specifications

Ok, so it seems that a lot of the information I needed was actually out there.... I was misinterpreting my data thinking the CAN was outputting the DLC value followed by the data value, when in fact I should be summing the two bytes into a single value..... :oops: Would still be useful to get a 'pap...