Search found 58 matches

by jezzpalmer
Fri Aug 02, 2019 6:20 pm
Forum: S6 GP/PnP Technical
Topic: R35 Coils - Wire direct?
Replies: 2
Views: 609

Re: R35 Coils - Wire direct?

Cheers Stevie. 8-)
by jezzpalmer
Thu Aug 01, 2019 7:57 pm
Forum: S6 GP/PnP Technical
Topic: R35 Coils - Wire direct?
Replies: 2
Views: 609

R35 Coils - Wire direct?

Hello, I've been running SR20 Splitfire coils on my 4G63 until now but they are struggling over 2 bar and I'm down to 0.5mm plug gap, which isn't great; so I've bought some R35 coils to replace them with. As far as I can tell the R35 coils have built in ignitors and the signal input can be wired dir...
by jezzpalmer
Wed Aug 24, 2016 4:10 pm
Forum: General Syvecs Chat
Topic: Output Testing.
Replies: 3
Views: 3815

Re: Output Testing.

Thanks Stevie, that seems so obvious now and it works. :)
Yeah you have to hold down or repeatedly press the + and - buttons to repeat the pulse.

Cheers,
Jezz.
by jezzpalmer
Tue Aug 23, 2016 9:21 pm
Forum: General Syvecs Chat
Topic: Output Testing.
Replies: 3
Views: 3815

Re: Output Testing.

Further to this I've just done some simple testing using a relay on an output (fuel10) If I use Input/Output testing to turn the state of fuel10 on and off nothing happens. If I assign fuel10 to a fan output and fiddle the switching temps I can switch the relay by toggling 'enable when engine stoppe...
by jezzpalmer
Tue Aug 23, 2016 7:53 pm
Forum: General Syvecs Chat
Topic: Output Testing.
Replies: 3
Views: 3815

Output Testing.

Hello, Today I tried to use the output testing feature to test my ignition and injector outputs; though with no success. Both base states are set to off, and I set a IGN pulse of 3ms and INJ of 5ms; then used + and - to send requests in the relevant pulse request section; but nothing appears to happ...
by jezzpalmer
Wed Aug 17, 2016 6:51 pm
Forum: S6 GP/PnP Technical
Topic: Output pin names, have they changed?
Replies: 9
Views: 16014

Re: Output pin names, have they changed?

Thanks Pat for confirming the output names, and also for the detailed explanation of the injector current draw.

Cheers,
Jezz.
by jezzpalmer
Sun Aug 14, 2016 5:33 pm
Forum: S6 GP/PnP Technical
Topic: Output pin names, have they changed?
Replies: 9
Views: 16014

Re: Output pin names, have they changed?

That's great, thanks for confirming.
I'll update my docs.

I'd expect the injector current draw to increase at higher absolute fuel pressures, but not sure if it's linear or not.
by jezzpalmer
Sun Aug 14, 2016 6:45 am
Forum: S6 GP/PnP Technical
Topic: Output pin names, have they changed?
Replies: 9
Views: 16014

Re: Output pin names, have they changed?

Thanks both. :) So I'm guessing that your fan was on PWM4 before, now on FUEL12, Stevie? I'm in the middle of assigning outputs and I'm just after clarification that this is how the pins have been renamed before something goes horribly wrong LOL. Can someone confirm that this is the new naming conve...
by jezzpalmer
Sat Aug 13, 2016 6:51 pm
Forum: S6 GP/PnP Technical
Topic: Output pin names, have they changed?
Replies: 9
Views: 16014

Output pin names, have they changed?

Hello, Have the AUX1-8 (PWM1-8) output been renamed FUEL 9-16 in later releases? Previous versions also gave the control board pin number alongside the output type and number, but in 1.69 I just see the output type and no control board number? Older version... outputs.JPG Latest 1.69 outputs.1.69.JP...
by jezzpalmer
Sat Jun 27, 2015 10:12 am
Forum: Feature Requests
Topic: Configurable Speed Output and maybe EHPS control?
Replies: 6
Views: 8725

Re: Configurable Speed Output and maybe EHPS control?

Thanks Steve, was looking at using the Dakota Digital SGI-5, but it's a bit spendy and a not that easy to get hold of.
I'll order one of these today and see how it goes, it would still be nice to be able to use an ECU output.